Is your Netgear Orbi satellite flashing white light? Do you know what it means to see a flashing white light on the Orbi satellite? It means your Orbi satellite is applying a configuration or a firmware update is under progress. There is nothing to be worried about. The flashing white ring light should go off after the changes have been successfully applied to the device. But it is worrisome when the ring light keeps on flashing for more than usual time. You need to do something about it. But what? Read the same in this blog.
Netgear Orbi whole-home WiFi mesh system helps you provide seamless internet coverage in the entire home. As every technical device needs updates, so does the Orbi system. Updating Orbi is an easy process, however, if you mess with the process, the firmware may get corrupted. This may also happen if the power supply fluctuated or the internet connection was disconnected. This causes the Orbi satellite flashing white light for a longer time than usual.
Apart from this, while making any changes to its configuration, if the power supply or internet connection were unstable or you performed a step incorrectly, the process may get interrupted. This may lead to a fault in the configurations. Thus, the Orbi satellite shows the problem through the continuous flashing white light.
As mentioned earlier, the poor power supply is one of the major reasons that can interrupt any configuration changes or firmware update process. So before you proceed with fixing the Orbi flashing white light, you MUST fix the power supply to the Orbi satellite.
To do this, you first need to check the power outlet that is used to supply power to the satellite. It should not be damaged. The power adapter should not be loose either. Apart from this, if there are a lot of power outage problems then use a UPS.
After you are done with fixing the power supply to the satellite, we want you to confirm that the internet connection is stable.
You can check with your ISP to get confirmation from his end regarding the same. Additionally, make sure that the satellite and router are connected properly. You can bring the satellite closer to the router if they are placed far from each other. Or you can connect them using an Ethernet cable to make sure that the connection between them is solid.
Note: Fixing the power and internet connection will make sure that any such issue does not occur again with your Orbi satellite. We would recommend you fix the power and internet connection to the Orbi router as well.
We shall now commence the troubleshooting process, wherein we will begin with rebooting the entire Orbi system. Rebooting is known to fix many minor to major issues with technical devices.
So, power off the Orbi router as well as the satellite. Do not forget to unplug them from the wall outlets which is more important. You need to wait for some time now. After waiting for a couple of minutes, plug the devices back and turn them on. See now if the Orbi satellite flashing white light issue has been fixed or not.
Orbi satellite flashing white light means it is not working properly. There are chances that the Orbi satellite and router are unable to communicate properly. We want you to resync them. In many cases, resyncing the devices have fixed similar issues.
Make sure that both devices are powered up completely. Thereafter press the Sync button on the Orbi router and then press the Sync button on the Orbi satellite. The Orbi devices are synced now.
If the Orbi satellite flashing white light issue hasn’t been fixed yet, then this means the firmware on the satellite got corrupted. This can only be fixed by resetting the satellite to the factory settings. By erasing the corrupted firmware and restoring the default factory settings, the satellite will begin behaving normally as it was when you purchased it.
You can reset the satellite by pressing the Reset button located on it. Do it immediately and restore the factory settings on it. After this set it up again.
You should update the firmware of the Orbi satellite now once again. Make sure that the process is not getting interrupted by any means. As you have fixed the power and internet connection, these can’t be the reason now. You need to take care that you do not perform any background activity while the firmware is getting installed on the satellite. Orbi satellite colors will help you make sure that the firmware is updated successfully after it is done.
This is how you can fix Orbi satellite flashing white light issues. If you are still stuck with the issue or want any support while updating firmware on Orbi, get in touch with our experts.
Disclaimer: orbiloginet.com is an independent information provider for a large variety of third-party products, brands, and services. Any use of trademarks, brands, products, and services is referential. We hereby disclaim any association, affiliation; direct or indirect, or representation in any form, of any such brand, product, or service.