Is Netgear Orbi Router Blinking White? Learn Here Why!

Each Netgear Orbi model has various LED lights located on it. One depicts the power status; the other depicts the connection between the Orbi router and satellite, and so on. Different Netgear Orbi light colors have different meanings. For example, if the Netgear Orbi router blinking white, then it means that your Netgear Orbi router is either powering up or attempting to connect after pressing the WPS button.

To ensure that the LED light successfully turns green, we have mentioned some tips in this blog post. Following them will help you to covert the blinking white to solid green. Given this, you ought to continue reading.

What to Do to Fix Orbi Router Blinking White Issue?

1. Check the Wall Socket in Use

Usually, after plugging in and pressing the power button, the Netgear Orbi router takes about 30 seconds to 1 minute in order to fully get powered up. Throughout this time, the LED light is blinking white. However, in case Netgear Orbi router blinking white continues for more than that, then it is a matter of concern.

It could be because the wall socket is either damaged or short-circuited or the device is not properly connected to it. In this scenario, here is what you can do:

1st Solution: Check the wall socket that is supplying power to your Orbi. In case it is damaged, then you need to get it repaired by calling an electrician at your house. By any chance, if this does not work for you, then you may plug the Orbi in some other outlet.

2nd Solution: Try to reconnect the Netgear Orbi router to the existing wall socket. Perhaps, it is not connected properly. Ensure that the connection is tight and that the device is not hanging loose, half in half out.

Now, see if the Netgear Orbi router blinking white issue has left following you around. What is that? Are you still facing it? Yes? Then you may read the tips given below.

2. Power Cycle the Netgear Router

Sometimes, a minor software or hardware technical glitch is enough to stop one from making good use of the device. Chances are that the Netgear Orbi router blinking white issue is bothering you due to the same reason. To troubleshoot it, you ought to consider restarting the networking device with the help of the following instructions:

1st Step: Locate the power button on the front panel of your Netgear Orbi router and press it. Soon the networking device will turn off.

2nd Step: Now, you need to wait for about 30 seconds. In case you want better results, then you may wait for maximum 5 minutes.

3rd Step: Have you waited enough? Well then, it is recommended that you power on the device by pressing the same button that you did in the 1st step.

It is recommended that you wait for the power LED light on the Netgear Orbi to become solid. This will act as an indication that your device has successfully powered up.

3. Reset the Netgear Orbi Router

Technical devices can be tricky. Sometimes, the reason why one may face issues with it can be unknown. In view of this, you should not step back from acknowledging that the reason why the Orbi router blinking white issue is bothering you could be unknown. But, know that knowing about the reason behind the issue is not needed to troubleshoot it. We can still be of use to you. You just need to reset the Orbi that you are using.

Now, the question is, how to restore Netgear Orbi router to the default values? For that, paying attention to troubleshooting tips mentioned here is needed:

1st Step: Locate the reset button on the Netgear Orbi router. You ought to be aware of one, i.e. the button is located inside the reset hole.

2nd Step: When you find it, press and hold it via an oil pin. You can also put a clip to use to do this but do not use the tip of a pen.

3rd Step: After that, you need to hold the reset button and wait for 5 minutes. Soon your networking device will reboot. Do not interrupt the process by unplugging the device.

As soon as you have read all three troubleshooting solutions, check again in case the Orbi router blinking white issue has been resolved or not.

Conclusion

We are anticipating that now that you have read all solutions mentioned above, you will no issues in troubleshooting the Orbi router blinking white issue. In case you do, then it could be because something is wrong with the router itself. In this case, you should consider the option of replacing it and setting it up again using the manual or web browser method. You can also use the Orbi app.